
A single projector can only fill so much space. Push it further back to make the image bigger and the picture gets dimmer and softer; keep it close and the image stays small. When you want a wall-sized panorama, a long interactive corridor or a floor that covers a whole play area, the answer is usually several projectors working together. Edge blending is what makes those projectors look like one.
This guide explains what edge blending is, how it works, what makes a blend look good or bad, and how to plan a multi-projector display, whether it is a passive image or an interactive floor or wall.
What is edge blending?
Edge blending is the technique of joining the images from two or more projectors so they appear as one large, seamless picture. Rather than placing the images exactly edge to edge, the projectors are set up so that neighbouring images overlap slightly. The brightness across each overlap is then faded: one projector fades out as the other fades in.
Why not just butt the images together? Because it is almost impossible to line two projected edges up perfectly, and they drift as the projectors warm up and the building moves. You end up with either a dark gap or a bright stripe where the images double up. A soft, faded overlap hides small misalignments and small differences between projectors far better than a hard join.
How the overlap works
Where two projectors shine on the same area, that strip receives light from both, so without correction it looks roughly twice as bright as the rest of the image. Blending software applies a gradient (a “blend ramp”) to each projector across the overlap so that, added together, the two contributions match the brightness of the rest of the picture.
A few practical points matter here:
- Overlap size. Projection specialists commonly suggest an overlap of around 10–20% of the image width. Too small an overlap tends to leave a visible line; a larger overlap gives a gentler, more forgiving transition but costs you some usable pixels.
- The shape of the fade. A straight linear fade can still be noticeable. Smoother curves, and gamma adjustment of the ramp, usually give a more invisible join.
- Geometry first. The images need to line up before they can blend. Geometric correction (often called warping) lets you nudge corners and edges so the overlapping content matches pixel for pixel.
It also helps to understand what you gain. As a simple example, two projectors that are each 1,920 pixels wide, overlapping by 15% (288 pixels), give a combined image of 3,552 pixels across: not quite double, because the overlap is shared. Add more projectors and the image keeps growing in the same way.
What makes a blend look seamless
Most visible joins come down to one of four things.
Mismatched projectors. Projectors vary in colour and brightness, even between units of the same model, and lamps and light sources change with age. Using the same model, brightness and resolution throughout, ideally bought together, makes blending far easier. Set them to the same picture mode, then match brightness and colour/white balance before blending.
Black level. No projector produces true black; it always emits a little light. In the overlap that faint light comes from two projectors, so on dark content the overlap can look like a slightly grey band. Software black-level adjustment can lift the rest of the image to match, but the effect is most noticeable in dark scenes and grows where several overlaps meet. The practical fix is often creative: content with brighter backgrounds and fewer pure-black areas hides joins far better.
Poor alignment. If the images are not mapped accurately, details appear doubled in the overlap. Mount projectors securely so they cannot creep, keep them as square-on to the surface as possible, and avoid relying on heavy keystone correction.
The surface. A smooth, even, matt surface shows a blend best. Glossy floors and walls create hot spots, and patterned or uneven surfaces break up the image regardless of how well it is blended.
Why edge blending is harder for interactive projection
For a video playing on a wall, a fraction of a second of processing delay rarely matters. For interactive projection it does. When someone steps on a floor effect or waves at a wall, the image needs to respond immediately or the illusion breaks. Some blending approaches, especially dedicated hardware processors or separate software layers, add a processing step between the content and the projector.
Interactive displays also need motion tracking that works across the whole blended image. A child running from one end of a floor to the other should not notice where one projector’s area ends and the next begins, and the effect should not hesitate at the join.
This is why our AdVis 2.1 interactive projection software has edge blending and edge overlap built in as standard. It works with every AdVis effect, can blend up to eight projectors with no processing overhead, and includes geometric correction so you can fit the blended image to the space. AdVis tracks movement across all of the tracking sensors and blended images, so people can move from one projector’s area to the next without noticing a join. For custom installations we can blend an unlimited number of projectors.
Planning a multi-projector display
A little planning before you buy equipment saves a lot of adjustment on site. Work through these steps:
- Measure the surface. Note the width and height (or length and width for a floor), plus the mounting height available.
- Choose the layout. Projectors can sit side by side for a wide wall, one after another down a corridor, or in a grid for a very large floor. Bear in mind that a grid creates areas where four images meet, which are the hardest to blend on dark content.
- Work out the throw. Use each projector’s throw ratio to see how large an image it makes from your mounting height, then allow for the overlap when calculating how many projectors you need.
- Match the hardware. Specify identical projectors, and check they are suitable for the mounting angle you need (for example pointing down at a floor).
- Plan the tracking. For interactive installations, we generally suggest one tracking kit per projector. AdVis can run up to eight projectors and eight tracking kits from one PC.
- Check the PC. Every projector needs a video output, and multi-projector effects need graphics power. A good Windows PC with a dedicated NVIDIA graphics card keeps things smooth.
- Align, then blend, then fine-tune. Get the physical position and focus right, correct the geometry, apply the blend, and finally check the result with test patterns and real content in the lighting conditions you will actually use.
Where edge blending is used
Once you can blend projectors, the size and shape of the display is limited mainly by the space and budget rather than by a single projector’s image. Common uses include:
- Large interactive floors covering halls, corridors and children’s play areas.
- Wide or tall interactive walls that react across the whole surface.
- Immersive rooms for museums, visitor attractions and events.
- Projection mapping onto large or irregular surfaces.
Edge blending FAQs
Do I need projectors with built-in edge blending?
Not with AdVis 2.1. Edge blending is built into the software as standard, so you do not need projectors with blending features or separate blending hardware.
How much should projector images overlap?
A common starting point is around 10–20% of the image width. The right figure depends on your projectors, content and surface, so it is worth testing on site.
Can I mix different projector models?
It is possible, but differences in brightness, colour and black level make the join much harder to hide. Matching models is strongly recommended.
Why can I see a grey band in dark scenes?
That is the black level of two projectors adding together in the overlap. Black-level adjustment and content with fewer pure-black areas both help.
Planning a large display?
If you are thinking about a display bigger than one projector can cover, send us the size of the space, the mounting height and how bright it is, and we will suggest a projector layout and tracking setup. Contact the Luminvision team to talk it through.